（清空日期可显示全部记录）
| 标准编号 | 标准名称 | 发布日期 | 实施日期 | 废止日期 | 替换信息 |
|---|---|---|---|---|---|
| ISO 15872:2017 | Aerospace -- UNJ threads -- Gauging | ||||
| ISO 80079-37:2016 | Explosive atmospheres -- Part 37: Non-electrical equipment for explosive atmospheres -- Non-electrical type of protection constructional safety ''c'', control of ignition sources ''b'', liquid immersion ''k'' | ||||
| ISO 25947-1:2017 | Fireworks -- Categories 1, 2 and 3 -- Part 1: Terminology | ||||
| ISO 25947-3:2017 | Fireworks -- Categories 1, 2 and 3 -- Part 3: Minimum labelling requirements | ||||
| ISO 26261-2:2017 | Fireworks -- Category 4 -- Part 2: Requirements | ||||
| ISO 4126-1:2004 | Safety devices for protection against excessive pressure -- Part 1: Safety valves | ||||
| ISO 4126-4:2004 | Safety devices for protection against excessive pressure -- Part 4: Pilot-operated safety valves | ||||
| ISO 12749-2:2013 | Nuclear energy, nuclear technologies, and radiological protection -- Vocabulary -- Part 2: Radiological protection | ||||
| ISO 4126-4:2013 | Safety devices for protection against excessive pressure -- Part 4: Pilot operated safety valves | ||||
| ISO 6718:1991 | Bursting discs and bursting disc devices | ||||
| ISO 1757:1996 | Personal photographic dosemeters | ||||
| ISO 1758:1976 | Direct-reading electroscope-type pocket exposure meters | ||||
| ISO 2889:1975 | General principles for sampling airborne radioactive materials | ||||
| ISO 8690:1988 | Decontamination of radioactively contaminated surfaces -- Method for testing and assessing the ease of decontamination | ||||
| ISO 11933-2:1997 | Components for containment enclosures -- Part 2: Gloves, welded bags, gaiters for remote - handling tongs and for manipulators | ||||
| ISO 11933-5:2001 | Components for containment enclosures -- Part 5: Penetrations for electrical and fluid circuits | ||||
| ISO 12749-4:2015 | Nuclear energy, nuclear technologies, and radiological protection -- Vocabulary -- Part 4: Dosimetry for radiation processing | ||||
| ISO 13164-2:2013 | Water quality -- Radon-222 -- Part 2: Test method using gamma-ray spectrometry | ||||
| ISO 15080:2001 | Nuclear facilities -- Ventilation penetrations for shielded enclosures | ||||
| ISO 15382:2015 | Radiological protection -- Procedures for monitoring the dose to the lens of the eye, the skin and the extremities | ||||
| ISO 21238:2007 | Nuclear energy -- Nuclear fuel technology -- Scaling factor method to determine the radioactivity of low- and intermediate-level radioactive waste packages generated at nuclear power plants | ||||
| ISO 21847-3:2007 | Nuclear fuel technology -- Alpha spectrometry -- Part 3: Determination of uranium 232 in uranium and its compounds | ||||
| ISO 22875 | Nuclear energy -- Determination of chlorine and fluorine in uranium dioxide powder and sintered pellets | ||||
| ISO/TR 8338:1988 | Crude petroleum oil -- Transfer accountability -- Method for estimation on ships of total quantity remaining on board (ROB) | ||||
| ISO 12917-1:2002 | Petroleum and liquid petroleum products -- Calibration of horizontal cylindrical tanks -- Part 1: Manual methods | ||||
| ISO 13739:2010 | Petroleum products -- Procedures for transfer of bunkers to vessels | ||||
| ISO 3928:1977 | Sintered metal materials, excluding hardmetals -- Fatigue test pieces | ||||
| ISO/WD TS 10108 | Steel -- Conversion of hardness values to tensile strength values | ||||
| ISO 10113:2006 | Metallic materials -- Sheet and strip -- Determination of plastic strain ratio | ||||
| ISO 10250:1994 | Metallic materials -- Hardness testing -- Tables of Knoop hardness values for use in tests made on flat surfaces | ||||
| ISO 11531:2015 | Metallic materials -- Sheet and strip -- Earing test | ||||
| ISO 11531:1994 | Metallic materials -- Earing test | ||||
| ISO 12004:1997 | Metallic materials -- Guidelines for the determination of forming-limit diagrams | ||||
| ISO 12004-1:2008 | Metallic materials -- Sheet and strip -- Determination of forming-limit curves -- Part 1: Measurement and application of forming-limit diagrams in the press shop | ||||
| ISO 10275:2007 | Metallic materials -- Sheet and strip -- Determination of tensile strain hardening exponent | ||||
| ISO 12004-2:2008 | Metallic materials -- Sheet and strip -- Determination of forming-limit curves -- Part 2: Determination of forming-limit curves in the laboratory | ||||
| ISO 12106:2003 | Metallic materials -- Fatigue testing -- Axial-strain-controlled method | ||||
| ISO 23788:2012 | Metallic materials -- Verification of the alignment of fatigue testing machines | ||||
| ISO/DIS 16837 | Non-destructive testing -- Acoustic emission inspection -- Test method for damage qualification of reinforced concrete beams | ||||
| ISO 3777:1976 | Radiographic inspection of resistance spot welds for aluminium and its alloys -- Recommended practice | ||||
| ISO/DIS 9692-4 | Welding and allied processes -- Recommendations for joint preparation -- Part 4: Clad steels | ||||
| ISO 10447:2006 | Resistance welding -- Peel and chisel testing of resistance spot and projection welds | ||||
| ISO/DIS 10042 | Welding -- Arc-welded joints in aluminium and its alloys -- Quality levels for imperfections | ||||
| ISO 3161:1977 | UNJ threads, with controlled root radius, for aerospace -- Inch series | ||||
| ISO 5855-2:1988 | Aerospace -- MJ threads -- Part 2: Limit dimensions for bolts and nuts | ||||
| ISO 15872:2002 | Aerospace -- UNJ threads -- Gauging | ||||
| ISO 10133:2000 | Small craft -- Electrical systems -- Extra-low-voltage d.c. installations | ||||
| ISO 5832-11:2014 | Implants for surgery -- Metallic materials -- Part 11: Wrought titanium 6-aluminium 7-niobium alloy | ||||
| ISO 5832-12:1996 | Implants for surgery -- Metallic materials -- Part 12: Wrought cobalt-chromium-molybdenum alloy | ||||
| ISO 5835:1991 | Implants for surgery -- Metal bone screws with hexagonal drive connection, spherical under-surface of head, asymmetrical thread -- Dimensions |
若您对上表中数据有任何疑问，请与网站联系。
