（清空日期可显示全部记录）
| 标准编号 | 标准名称 | 发布日期 | 实施日期 | 废止日期 | 替换信息 |
|---|---|---|---|---|---|
| AS4825 | Gasket, Fitting End, 24脗掳 Cone | ||||
| AS4828A | Technical Manual Requirements for Ground Support Equipment | ||||
| J1899_200006 | Lubricating Oil, Aircraft Piston Engine (Ashless Dispersant) | ||||
| J755_201505 | Marine Propeller-Shaft Ends and Hubs | ||||
| J1899_200508 | Lubricating Oil, Aircraft Piston Engine (Ashless Dispersant) | ||||
| AS7365/7 | Band, Male Coupling, 12 Inch Air Duct | ||||
| AS7365/6 | Band, Female Coupling, 12 Inch Air Duct | ||||
| AS7283A | Gaskets, Type Xx Engine Accessory Drive Corrosion Resistant Steel Screen Reinforced Controlled Performance | ||||
| AS7283B | Gaskets, Type Xx Engine Accessory Drive Corrosion Resistant Steel Screen Reinforced Controlled Performance | ||||
| AS7330 | Rings, Retaining - Spiral Wound, Uniform Section Corrosion Resistant Steel Procurement Specification For | ||||
| AS7325B | Gasket, Metal O-Ring Corrosion and Heat Resistant Steel Procurement Specification For | ||||
| AS7325 | Gasket, Metal O-Ring Corrosion and Heat Resistant Steel Procurement Specification For | ||||
| AS7325A | Gasket, Metal O-Ring Corrosion and Heat Resistant Steel Procurement Specification for | ||||
| AS7351 | Clamp, Loop Type Bonding | ||||
| AS7351A | CLAMP, LOOP TYPE BONDING | ||||
| AS7252A | Nuts, Self-Locking, Steel High Strength, All Metal 450 脗掳F Use, UN and UNJ Thread Form | ||||
| AS7251C | Nuts, Self-Locking, Steel, Corrosion and Heat Resistant High Strength, All Metal 1200 脗掳F Use, UNJ Thread Form | ||||
| AS7252 | Nuts, Self-Locking, Steel High Strength, All Metal 450 脗掳F Use, UNJ Thread Form | ||||
| AS7458A | Studs, Steel, Low Alloy, Heat Resistant, Normalized and Tempered, Roll Threaded, 135 000 psi Tensile Strength | ||||
| AS7283 | Gaskets, Type Xx Engine Accessory Drive Corrosion Resistant Steel Screen Reinforced Controlled Performance | ||||
| AS7455 | Bolts and Screws, Steel, Low Alloy, Heat Resistant Hardened and Tempered, Roll Threaded | ||||
| AS7200/1 | National Aerospace and Defense Contractors Accreditation Program (NADCAP) Audit and Inspection Procedures and Checklists for the Sealant Manufacturers Accreditation Program | ||||
| AS714A | Aircraft Hydraulic Start Motor | ||||
| AS7201 | National Aerospace and Defense Contractors Accreditation Program (Nadcap) Requirements for Accreditation of Pass-Thru Distributors | ||||
| AS7200/1A | National Aerospace and Defense Contractors Accreditation Program (Nadcap) Audit and Inspection Procedures and Checklists for the Sealant Manufacturers Accreditation Program | ||||
| AS7119A | Nadcap Aerospace Standard for Electronics Printed Circuit Board | ||||
| AS7119 | Nadcap Aerospace Standard for Electronics Printed Circuit Board | ||||
| AS7455A | Bolts and Screws, Steel, Low Alloy, Heat Resistant Hardened and Tempered, Roll Threaded | ||||
| AS714 | Aircraft Hydraulic Start Motor | ||||
| AS7119B | Nadcap Aerospace Standard for Electronics Printed Circuit Boards(Cancelled Jan 2015) | ||||
| AS7118/3 | Nadcap Requirements for Core Processing | ||||
| AS7118/2A | Nadcap Requirements for Metal Bonding(Cancelled Jul 2008) | ||||
| AS7118/3A | Nadcap Requirements for Core Processing(Cancelled Jul 2008) | ||||
| AS7118A | Nadcap Requirements for Composites(Cancelled Jul 2008) | ||||
| AS7118/1A | Nadcap Requirements for Prepreg/Adhesive Bonding(Cancelled Jul 2008) | ||||
| AS7118/1 | Nadcap Requirements for Prepreg/Adhesive Bonding | ||||
| AS7118 | Nadcap Requirements for Composites | ||||
| AS7118/2 | Nadcap Requirements for Metal Bonding | ||||
| AS7116/4A | National Aerospace and Defense Contractors Accreditation Program, Requirements for Laser Beam Machining (LBM)(Cancelled Jul 2008) | ||||
| AS5116B | Minimum Operational Performance Specification for Ground Ice Detection Systems | ||||
| AS7116A | National Aerospace and Defense Contractors Accreditation Program, Requirements for Nonconventional Machining(Cancelled Jul 2008) | ||||
| AS7117A | National Aerospace and Defense Contractors Accreditation Program, Requirements for Shot Peening, Peen Forming, Glass Bead Peening(Cancelled Jul 2008) | ||||
| AS7117 | National Aerospace and Defense Contractors Accreditation Program Requirements for Shot Peening, Peen Forming, Glass Bead Peening | ||||
| AS7250 | Nuts, Self-Locking, Steel, Corrosion and Heat Resistant High Strength, All Metal 1200 脗掳F Use, UN Thread Form | ||||
| AS7246 | Inserts, Screw Thread, Helical Coil 72ni 15.5cr 0.95(Cb+Ta) 2.5ti 0.70al 7.0fe Corrosion and Heat Resistant Alloy Procurement Specification For | ||||
| AS7245A | Inserts, Screw Thread, Helical Coil 19Cr-9.2Ni, Corrosion Resistant Steel, Procurement Specification For | ||||
| AS7245 | Inserts, Screw Thread, Helical Coil 19cr 9.2ni, Corrosion Resistant Steel, Procurement Specification For | ||||
| AS7241A | Washers, Spring Lock, Corrosion Resistant Steel 18Cr - 9Ni (UNS S30200), Procurement Specification for | ||||
| AS7240A | Washers, Spring Lock, Carbon Steel, Procurement Specification for(STABILIZED Feb 2015) | ||||
| AS7241 | Washers, Spring Lock, Corrosion Resistant Steel 18Cr - 9Ni (UNS S30200), Procurement Specification for |
若您对上表中数据有任何疑问，请与网站联系。
