（清空日期可显示全部记录）
| 标准编号 | 标准名称 | 发布日期 | 实施日期 | 废止日期 | 替换信息 |
|---|---|---|---|---|---|
| BS EN 1987-1:1997 | Electrically propelled road vehicles. Specific requirements for safety. On board energy storage | ||||
| BS EN 1987-2:1997 | Electrically propelled road vehicles. Specific requirements for safety. Functional safety means and protection against failures | ||||
| BS EN 1987-3:1998 | Electrically propelled road vehicles. Specific requirements for safety. Protection of users against electrical hazards | ||||
| BS AU 200-2a:1984 | Spray reducing devices for heavy goods vehicles. Specification for performance of suppression material and devices, and air/water separating material and devices | ||||
| BS AU 200-1a:1984 | Spray reducing devices for heavy goods vehicles. Specification for design of containment devices | ||||
| BS AU 1c:1989 | Specification for dimensions of '50' fifth wheel king pin for semi-trailers | ||||
| DD ISO/TS 20100:2008 | Gaseous hydrogen. Fuelling stations | ||||
| PAS 2012-2:2015 | Specification For M1 Vehicles For The Carriage Of One Or More Passengers Seated In Wheelchairs - Part 2: Retail Requirements | ||||
| BS AU 203a:1988 | Specification for dimensions of couplings between power take offs (PTOs) and ancillary driven units on commercial road vehicles | ||||
| BS AU 206-4:1986 | Diagnostic systems for road vehicles. Specification for general requirements for testing electronic systems | ||||
| BS ISO 20826:2006 | Automotive Lpg Components - Containers | ||||
| DD 208:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines: specification for rectangular rings with narrow ring width | ||||
| BS AU 209-1a:1992 | Vehicle security. Specification for locking systems for passenger cars and car derived vehicles | ||||
| BS AU 209-2:1988 | Vehicle security. Specification for security systems against theft of in-car equipment for entertainment and communication purposes | ||||
| BS AU 209-0:1996 | Vehicle security. Guide to the application of security devices/systems to vehicles | ||||
| DD 209:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines: specification for half keystone rings | ||||
| BS ISO 20860-2:2009 | Road vehicles. 50 ohms impedance radio frequency connection system interface. Test procedures | ||||
| BS ISO 20860-1:2008 | Road vehicles. 50 ohms impedance radio frequency connection system interface. Dimensions and electrical requirements | ||||
| BS ISO 20828:2006 | Road vehicles. Security certificate management | ||||
| BS AU 210-2:1994 | Drawbars for caravans and light trailers. Specification for the design of aluminium drawbars and chassis | ||||
| BS ISO 20918:2007 | Road vehicles. Braking threshold pressures for heavy commercial vehicle combinations with fully pneumatic braking systems. Test with roller brake tester | ||||
| BS AU 209-8:1997 | Vehicle security. Specification for locking systems for goods vehicle load compartments | ||||
| BS AU 209-6a:1996 | Vehicle security. Specification for dead locking systems for passenger cars and car derived vehicles | ||||
| BS AU 209-7:1993 | Vehicle security. Specification for locking systems for goods vehicle driver's compartments | ||||
| BS AU 209-5b:1996 | Vehicle security. Specification for central power locking systems for passenger cars and car derived vehicles | ||||
| BS AU 209-4a:1995 | Vehicle security. Specification for security glazing for passenger cars and car derived vehicles | ||||
| BS AU 209-3:1988 | Vehicle security. Specification for security marking of glazing for passenger cars and car derived vehicles | ||||
| PAS 2012-1:2015 | Specification For M1 Vehicles For The Carriage Of One Or More Passengers Seated In Wheelchairs - Part 1: Manufacturing Requirements | ||||
| DD ISO/PAS 21308-1:2007 | Road vehicles. Product data exchange between chassis and bodywork manufacturers (BEP). General principles | ||||
| BS ISO 21069-2:2008 | Road vehicles. Test of braking systems on vehicles with a maximum authorized total mass of over 3,5 t using a roller brake tester. Air over hydraulic and purely hydraulic braking systems | ||||
| BS AU 214-3:1988 | Gearbox flanges. Specification for dimensions for type S gearbox flanges for commercial vehicles and buses | ||||
| BS AU 214-2:1988 | Gearbox flanges. Specification for dimensions for type A gearbox flanges for commercial vehicles and buses | ||||
| BS ISO 21308-3:2007 | Road vehicles. Product data exchange between chassis and bodywork manufacturers (BEP). General, mass and administrative exchange parameters | ||||
| BS ISO 21308-2:2006 | Road vehicles. Product data exchange between chassis and bodywork manufacturers (BEP). Dimensional bodywork exchange parameters | ||||
| BS AU 217-1a:1987 | Maximum road speed limiters for motor vehicles. Specification for installed requirements | ||||
| BS AU 216-1:1987 | Hydraulic brake systems using petroleum base brake fluids for road vehicles. Specification for petroleum base reference fluid | ||||
| BS AU 215-3:1988 | Power take offs (PTOs). Specification for dimensions of connections for rear mounted power take offs for commercial road vehicles | ||||
| BS AU 215-2:1987 | Power take offs (PTOs). Specification for dimensions of side openings for commercial road vehicles | ||||
| BS AU 215-1:1987 | Power take offs (PTOs). Specification for dimensions for clearance envelope for commercial road vehicles | ||||
| BS AU 214a-1:1987 | Gearbox flanges. Specification for dimensions of cross-tooth gearbox flanges, type T, for commercial vehicles and buses | ||||
| BS ISO 21994:2007 | Passenger cars. Stopping distance at straight-line braking with ABS. Open-loop test method | ||||
| BS ISO 21848:2005 | Road vehicles. Electrical and electronic equipment for a supply voltage of 42 V. Electrical loads | ||||
| BS AU 217-2:1989 | Maximum road speed limiters for motor vehicles. Specification for system and component requirements | ||||
| BS ISO 22179:2009 | Intelligent transport systems. Full speed range adaptive cruise control (FSRA) systems. Performance requirements and test procedures | ||||
| BS ISO 22178:2009 | Intelligent transport systems. Low speed following (LSF) systems. Performance requirements and test procedures | ||||
| BS ISO 22168:2006 | Road vehicles. Holding test of coatings influencing the colour of light emitted by light sources). Test methods | ||||
| BS ISO 21995:2008 | Road vehicles. Test of vehicle air braking systems with a permissible mass of over 3,5 t. Acquisition and use of reference values using a roller brake tester | ||||
| BS ISO 22241-1:2006 | Diesel engines. NOx reduction agent AUS 32. Quality requirements | ||||
| DD ISO/TS 22240:2008 | Road vehicles. Vehicles safety information model (VSIM) | ||||
| BS AU 222:1988 | Method of evaluating surface and material flaws of disc brake pads after testing |
若您对上表中数据有任何疑问，请与网站联系。
