（清空日期可显示全部记录）
| 标准编号 | 标准名称 | 发布日期 | 实施日期 | 废止日期 | 替换信息 |
|---|---|---|---|---|---|
| ISO 15765-4:2011 | Road vehicles - Diagnostic communication over Controller Area Network (DoCAN) - Part 4: Requirements for emissions-related systems | ||||
| ISO/TS 15827:2007 | Road vehicles - Test procedures - Evaluating small female dummy arm and forearm interactions with driver frontal airbags and side airbags | ||||
| ISO 15830-1:2013 | Road vehicles - Design and performance specifications for the WorldSID 50th percentile male side-impact dummy - Part 1: Terminology and rationale | ||||
| ISO 15829:2013 | Road vehicles - Side impact test procedures for the evaluation of occupant interactions with side airbags by pole impact simulation | ||||
| ISO 15828:2004 | Road vehicles - Offset frontal impact test procedure | ||||
| ISO 1585:1992 | Road vehicles - Engine test code - Net power | ||||
| ISO 15830-4:2013 | Road vehicles - Design and performance specifications for the WorldSID 50th percentile male side impact dummy - Part 4: User's manual | ||||
| ISO 15830-3:2013 | Road vehicles - Design and performance specifications for the WorldSID 50th percentile male side-impact dummy - Part 3: Electronic subsystems | ||||
| ISO 15830-2:2013 | Road vehicles - Design and performance specifications for the WorldSID 50th percentile male side-impact dummy - Part 2: Mechanical subsystems | ||||
| ISO/TS 15869:2009 | Gaseous hydrogen and hydrogen blends - Land vehicle fuel tanks | ||||
| ISO 16121-4:2011 | Road vehicles - Ergonomic requirements for the driver's workplace in line-service buses - Part 4: Cabin environment | ||||
| ISO 16121-3:2011 | Road vehicles - Ergonomic requirements for the driver's workplace in line-service buses - Part 3: Information devices and controls | ||||
| ISO 16121-2:2011 | Road vehicles - Ergonomic requirements for the driver's workplace in line-service buses - Part 2: Visibility | ||||
| ISO 16121-1:2012 | Road vehicles - Ergonomic requirements for the driver's workplace in line-service buses - Part 1: General description, basic requirements | ||||
| ISO 16185:2000 | Road vehicles - Engine families for certification of heavy-duty vehicles by Exhaust emission | ||||
| ISO 16183:2002 | Heavy duty engines - Measurement of gaseous emissions from raw exhaust gas and of particulate emissions using partial flow dilution systems under transient test conditions | ||||
| ISO 16154:2005 | Tractors and machinery for agriculture and forestry - Installation of lighting, light signalling and marking devices for travel on public roadways | ||||
| ISO 16232-1:2007 | Road vehicles - Cleanliness of components of fluid circuits - Part 1: Vocabulary | ||||
| ISO 16232-2:2007 | Road vehicles - Cleanliness of components of fluid circuits - Part 2: Method of extraction of contaminants by agitation | ||||
| ISO 16232-10:2007 | Road vehicles - Cleanliness of components of fluid circuits - Part 10: Expression of results | ||||
| ISO 16232-3:2007 | Road vehicles - Cleanliness of components of fluid circuits - Part 3: Method of extraction of contaminants by pressure rinsing | ||||
| ISO 16232-4:2007 | Road vehicles - Cleanliness of components of fluid circuits - Part 4: Method of extraction of contaminants by ultrasonic techniques | ||||
| ISO 16232-7:2007 | Road vehicles - Cleanliness of components of fluid circuits - Part 7: Particle sizing and counting by microscopic analysis | ||||
| ISO 16232-6:2007 | Road vehicles - Cleanliness of components of fluid circuits - Part 6: Particle mass determination by gravimetric analysis | ||||
| ISO 16232-5:2007 | Road vehicles - Cleanliness of components of fluid circuits - Part 5: Method of extraction of contaminants on functional test bench | ||||
| ISO 16232-9:2007 | Road vehicles - Cleanliness of components of fluid circuits - Part 9: Particle sizing and counting by automatic light extinction particle counter | ||||
| ISO 16232-8:2007 | Road vehicles - Cleanliness of components of fluid circuits - Part 8: Particle nature determination by microscopic analysis | ||||
| ISO 16234:2006 | Heavy commercial vehicles and buses - Straight-ahead braking on surfaces with split coefficient of friction - Open-loop test method | ||||
| ISO/TR 16250:2013 | Road vehicles - Objective rating metrics for dynamic systems | ||||
| ISO 16247:2004 | Road vehicles - Detection of exhaust system leaks - Helium test method and detection device specification | ||||
| ISO/TR 16352:2005 | Road vehicles - Ergonomic aspects of in-vehicle presentation for transport information and control systems - Warning systems | ||||
| ISO/TS 16332:2006 | Diesel engines - Fuel filters - Method for evaluating fuel/water separation efficiency | ||||
| ISO 16333:2011 | Heavy commercial vehicles and buses - Steady-state rollover threshold - Tilt-table test method | ||||
| ISO 16505:2015 | Road vehicles - Ergonomic and performance aspects of Camera Monitor Systems - Requirements and test procedures | ||||
| ISO 16552:2014 | Heavy commercial vehicles and buses - Stopping distance in straight-line braking with ABS - Open loop and closed loop test methods | ||||
| ISO 16673:2007 | Road vehicles - Ergonomic aspects of transport information and control systems - Occlusion method to assess visual demand due to the use of in-vehicle systems | ||||
| ISO 16750-2:2012 | Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 2: Electrical loads | ||||
| ISO 16750-1:2006 | Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 1: General | ||||
| ISO 16750-5:2010 | Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 5: Chemical loads | ||||
| ISO 16750-4:2010 | Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 4: Climatic loads | ||||
| ISO 16750-3:2012 | Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 3: Mechanical loads | ||||
| ISO 16844-2:2011 | Road vehicles - Tachograph systems - Part 2: Electrical interface with recording unit | ||||
| ISO 16844-1:2013 | Road vehicles - Tachograph systems - Part 1: Electrical connectors | ||||
| ISO 16833:2006 | Road vehicles - Wheels - Measurement of radial and lateral run-out | ||||
| ISO 16844-6:2015 | Road vehicles - Tachograph systems - Part 6: Diagnostics | ||||
| ISO 16844-5:2004 | Road vehicles - Tachograph systems - Part 5: Secured CAN interface | ||||
| ISO 16844-4:2015 | Road vehicles - Tachograph systems - Part 4: CAN interface | ||||
| ISO 16844-3:2004/Cor 1:2006 | Road vehicles - Tachograph systems - Part 3: Motion sensor interface - Technical Corrigendum 1 | ||||
| ISO 16844-3:2004 | Road vehicles - Tachograph systems - Part 3: Motion sensor interface | ||||
| ISO 16844-7:2015 | Road vehicles - Tachograph systems - Part 7: Parameters |
若您对上表中数据有任何疑问，请与网站联系。
