（清空日期可显示全部记录）
| 标准编号 | 标准名称 | 发布日期 | 实施日期 | 废止日期 | 替换信息 |
|---|---|---|---|---|---|
| ISO 7622-2:1984 | Steel cord conveyor belts -- Longitudinal traction test -- Part 2: Measurement of tensile strength | ||||
| ISO 7623:1996 | Steel cord conveyor belts -- Cord-to-coating bond test -- Initial test and after thermal treatment | ||||
| ISO 7623:2015 | Steel cord conveyor belts -- Cord-to-coating bond test -- Initial test and after thermal treatment | ||||
| ISO 9856:2003 | Conveyor belts -- Determination of elastic and permanent elongation and calculation of elastic modulus | ||||
| ISO 14890:2013 | Conveyor belts -- Specification for rubber- or plastics-covered conveyor belts of textile construction for general use | ||||
| ISO 15236-1:2016 | Steel cord conveyor belts -- Part 1: Design, dimensions and mechanical requirements for conveyor belts for general use | ||||
| ISO 15236-2:2017 | Steel cord conveyor belts -- Part 2: Preferred belt types | ||||
| ISO 15236-3:2017 | Steel cord conveyor belts -- Part 3: Special safety requirements for belts for use in underground installations | ||||
| ISO 18573:2012 | Conveyor belts -- Test atmospheres and conditioning periods | ||||
| ISO 21181:2013 | Light conveyor belts -- Determination of the relaxed elastic modulus | ||||
| ISO 5893:1993 | Rubber and plastics test equipment -- Tensile, flexural and compression types (constant rate of traverse) -- Description | ||||
| ISO 3019-2:2001/Cor 1:2006 | |||||
| ISO 4094:1991 | Paper, board and pulps -- International calibration of testing apparatus -- Nomination and acceptance of standardizing and authorized laboratories | ||||
| ISO 638:1978 | Pulps -- Determination of dry matter content | ||||
| ISO 779:1982 | Pulps -- Determination of iron content -- 1,10-Phenanthroline photometric and flame atomic absorption spectrometric methods | ||||
| ISO 3260:2015 | Pulps -- Determination of chlorine consumption (Degree of delignification) | ||||
| ISO 5350-2:1998 | Pulp -- Estimation of dirt and shives -- Part 2: Inspection of mill sheeted pulp | ||||
| ISO/TR 25477:2008 | Paper, board and pulps - Basic guidelines for image analysis measurements | ||||
| ISO/R 135:1959 | Paper vocabulary -- Second series of terms | ||||
| ISO/DIS 287 | Paper and board -- Determination of moisture content of a lot -- Oven-drying method | ||||
| ISO 8791-4:2007 | Paper and board -- Determination of roughness/smoothness (air leak methods) -- Part 4: Print-surf method | ||||
| ISO/DIS 6182-12 | Fire protection -- Automatic sprinkler systems -- Part 12: Requirements and test methods for grooved-end components for steel pipe systems | ||||
| ISO 10597:2004 | Road vehicles -- Flat attachment fixing nuts for commercial vehicles -- Test methods | ||||
| ISO 12239:2010 | Smoke alarms using scattered light, transmitted light or ionization | ||||
| ISO/TR 5924:1989 | Fire tests -- Reaction to fire -- Smoke generated by building products (dual-chamber test) | ||||
| ISO/TR 6543:1979 | The development of tests for measuring toxic hazards in fire | ||||
| ISO 7077:1981 | Measuring methods for building -- General principles and procedures for the verification of dimensional compliance | ||||
| ISO 15875-1:2003/Amd 1:2007 | |||||
| ISO/CD 21426 | Tourism and related services -- Medical spa -- Service requirements | ||||
| ISO 1132:1980 | Rolling bearings -- Tolerances -- Definitions | ||||
| ISO/NP 13988 | Passenger vehicle wheels -- Clip balance weight and rim flange nomenclature, test procedures and performance requirements | ||||
| ISO/IEC 10164-11:1994/Amd 1:1998 | Implementation conformance statement proformas | ||||
| ISO 5248:2003 | Textile machinery and accessories -- Dyeing and finishing machinery -- Vocabulary for ancillary devices | ||||
| ISO 8114:1990 | Textile machinery and accessories -- Spindles for ring-spinning and doubling machines -- List of equivalent terms | ||||
| ISO 4720:1992 | Essential oils -- Nomenclature | ||||
| ISO 19403-7 | Paints and varnishes -- Wettability -- Part 7: Measurement of the contact angle on a tilt stage (roll-off angle) | ||||
| ISO/TS 17261:2005/Cor 1:2005 | |||||
| ISO/IEC 14443-2:2001/Amd 1:2005/Cor 1:2007 | |||||
| ISO/DIS 31000 | Risk management -- Guidelines | ||||
| ISO/TR 11044:2008 | Water quality -- Scientific and technical aspects of batch algae growth inhibition tests | ||||
| ISO/IEEE 11073-30200:2004/Amd 1:2015 | |||||
| ISO 17631:2002/Cor 1:2002 | |||||
| ISO/IEC 9594-3:2005/Cor 2:2009 | |||||
| ISO 7886-1:1993 | Sterile hypodermic syringes for single use -- Part 1: Syringes for manual use | ||||
| ISO 8359:1988 | Oxygen concentrators for medical use -- Safety requirements | ||||
| ISO 8600-4:1997 | Optics and optical instruments -- Medical endoscopes and certain accessories -- Part 4: Determination of maximum width of insertion portion | ||||
| ISO 10637:1999 | Dental equipment -- High- and medium-volume suction systems | ||||
| ISO 5002:1999 | Hot-rolled and cold-reduced electrolytic zinc-coated carbon steel sheet of commercial and drawing qualities | ||||
| ISO 9359:1989 | Air quality -- Stratified sampling method for assessment of ambient air quality | ||||
| ISO 14644-2:2000 | Cleanrooms and associated controlled environments -- Part 2: Specifications for testing and monitoring to prove continued compliance with ISO 14644-1 |
若您对上表中数据有任何疑问，请与网站联系。
