（清空日期可显示全部记录）
| 标准编号 | 标准名称 | 发布日期 | 实施日期 | 废止日期 | 替换信息 |
|---|---|---|---|---|---|
| EN 12570-2000 | Industrial Valves - Method for Sizing the Operating Element | ||||
| EN 12573-1-2000 | Welded Static Non-Pressurized Thermoplastic Tanks - Part 1: General Principles | ||||
| EN 12573-2-2000 | Welded Static Non-Pressurized Thermoplastic Tanks - Part 2: Calculation of Vertical Cylindrical Tanks | ||||
| EN 12573-3-2000 | Welded Static Non-Pressurized Thermoplastic Tanks - Part 3: Design and Calculation for Single Skin Rectangular Tanks | ||||
| EN 12575-1998 | Plastics - Thermoset Moulding Compounds - Determination of the Degree of Fibre Wet out in SMC | ||||
| EN 12576-1998 | Plastics - Fibre Reinforced Composites - Preparation of Compression Moulded Test Plates of SMC, BMC and DMC | ||||
| EN 12580-1999 | Soil Improvers and Growing Media - Determination of a Quantity | ||||
| EN 12582-1999 | Surface Active Agents - Determination of the Polyethylene Glycol Content According to Molar Mass in Non-Ionic Surface Active Agents (Ethoxylated) by HPLC/ELSD | ||||
| EN 12583-2000 | Gas Supply Systems - Compressor Stations - Functional Requirements | ||||
| EN 12584-1999 | Imperfections in Oxyfuel Flame Cuts, Lazer Beam Cuts and Plasma Cuts - Terminology | ||||
| EN 12589-2001 | Ventilation for Buildings - Air Terminal Units - Aerodynamic Testing and Rating of Constant and Variable Rate Terminal Units | ||||
| EN 12600-2002 | Glass in building - Pendulum test - Impact test method and classification for flat glass | ||||
| EN 12604-2000 | Industrial, Commercial and Garage Doors and Gates - Mechanical Aspects - Requirements | ||||
| EN 12605-2000 | Industrial, Commercial and Garage Doors and Gates - Mechanical Aspects - Test Methods | ||||
| EN 1261-1995 | Fibre Ropes for General Service - Hemp | ||||
| EN 12615-1999 | Products and Systems for the Protection and Repair of Concrete Structures - Test Methods - Determination of Slant Shear Strength | ||||
| EN 12616-2003 | Surfaces for sports areas Determination of water infiltration rate | ||||
| EN 12617-1-2003 | Products and systems for the protection and repair of concrete structures Test methods Part 1: Determination of linear shrinkage for polymers and surface protection systems (SPS) | ||||
| EN 12617-3-2002 | Products and Systems for the Protection and Repair of Concrete Structures - Test Methods - Part 3: Determination of Early Age Linear Shrinkage for Structural Bonding Agents | ||||
| EN 12618-1-2003 | Products and systems for the protection and repair of concrete structures - Test methods - Part 1: Adhesion and elongation capacity of injection products with limited ductility | ||||
| EN 1262-2003 | Surface active agents - Determination of pH value of solutions or dispersions | ||||
| EN 12625-3-1999 | Tissue Paper and Tissue Products - Part 3: Determination of Thickness, Bulking Thickness and Apparent Bulk Density Superseded by EN ISO 12625-3:2005 | ||||
| EN 2155-12-1997 | Aerospace Series - Test Methods for Transparent Materials for Aircraft Glazing - Part 12: Determination of Linear Thermal Expansion | ||||
| EN 2155-13-1993 | Aerospace Series Test Methods for Transparent Materials for Aircraft Glazing Part 13: Determination of Temperature at Deflection Under Load | ||||
| EN 2155-19-1996 | Aerospace Series - Test Methods for Transparent Materials for Aircraft Glazing - Part 19: Determination of Craze Resistance | ||||
| EN 2155-7-1997 | Aerospace Series - Test Methods for Transparent Materials for Aircraft Glazing - Part 7: Determination of Optical Deviation | ||||
| EN 2157-1-1993 | Aerospace Series Steel Forging Stock and Forgings Technical Specifications Part 1 - General Requirements | ||||
| EN 2157-2-1993 | Aerospace Series Steel Forging Stock and Forgings Technical Specification Part 2 - Forging Stock | ||||
| EN 2162-1-1996 | Technical Product Documentation - Springs - Part 1 : Simplified Representation (ISO 2162-1 : 1993) | ||||
| EN 22063-1993 | Metallic and Other Inorganic Coatings - Thermal Spraying - Zinc, Aluminium and Their Alloys (ISO 2063 : 1991 Modified) | ||||
| EN 22401-1994 | Covered Electrodes - Determination of the Efficiency, Metal Recovery and Deposition Coefficient (ISO 2401 : 1972) | ||||
| EN 22553-1994 | Welded, Brazed and Soldered Joints - Symbolic Representation on Drawings (ISO 2553 : 1992) | ||||
| EN 2257-1997 | Aerospace Series - Circular Tubes for Structures in Aluminium and Aluminium Alloys - Diameter 6 mm Less Than or Equal to D Less Than or Equal to 100 mm - Thickness 1 mm Less Than or Equal to a Less Than or Equal to 6 mm - Dimensions | ||||
| EN 2258-1997 | Aerospace Series - Circular Tubes for Fluids in Aluminium and Aluminium Alloys - Diameter 3,2 mm Less Than or Equal to D Less Than or Equal to 100 mm - Thickness 0,6 mm Less Than or Equal to a Less Than or Equal to 2,5 mm - Dimensions | ||||
| EN 2259-1995 | Aerospace Series - Silicone Rubber (VMQ) - Hardness 50 IRHD | ||||
| EN 2261-1995 | Aerospace Series - Silicone Rubber (VMQ) - Hardness 70 IRHD | ||||
| EN 2262-1995 | Aerospace Series - Silicone Rubber (VMQ/PVMQ) with High Tear Strength - Hardness 50 IRHD | ||||
| EN 2264-1996 | Aerospace Series - Nuts, Anchor, Self-Locking, Floating, Two- Lug, Incremental Counterbore, in Alloy Steel, Cadmium Plated MoS2 Lubricated - Classification : 900 MPa (at Ambient Temperature) /235 Degrees C | ||||
| EN 2290-1-1998 | Aerospace Series - Rod Bodies, Flight Control in Aluminium Alloy, for Adjustable End Fittings - Part 1: Dimensions and Loads | ||||
| EN 2330-1993 | Aerospace Series - Textile Glass Fibre Preimpregnates - Test Method for the Determination of the Content of Volatile Matter | ||||
| EN 23312-1993 | Sintered Metal Materials and Hardmetals - Determination of Young Modulus (ISO 3312: 1987) | ||||
| EN 2332-1993 | Aerospace Series - Textile Glass Fibre Preimpregnates - Test Method for the Determination of the Resin Flow | ||||
| EN 2334-1997 | Aerospace Series - Chromic-Sulphuric Acid Pickle of Aluminium and Aluminium Alloys | ||||
| EN 2339-2001 | Aerospace Series - Sheets, Cold Rolled in Titanium and Titanium Alloys - Thickness 0,2 mm Less Than or Equal to a Less Than or Equal to 6 mm - Dimensions | ||||
| EN 2344-2001 | Aerospace Series - Round Bars, Machined in Heat Resisting Alloys - Diameter 10 mm Less Than or Equal to D Less Than or Equal to 180 mm - Dimensions | ||||
| EN 235-2001 | Wallcoverings - Vocabulary and Symbols | ||||
| EN 2363-1989 | Locking Clips for Turnbuckles of Control Cables Dimensions | ||||
| EN 23923-2-1993 | Metallic Powders - Determination of Apparent Density - Part 2: Scott Volumeter Method (ISO 3923-2: 1981) | ||||
| EN 24-1975 | Doors: Measurement of Defects of General Flatness of Door Leaves | ||||
| EN 2413-1995 | Aerospace Series - Bolts, Shouldered, Thin Hexagonal Head, Close Tolerance Shank, Short Thread, in Alloy Steel, Cadmium Plated - Classification: 1 100 MPa (at Ambient Temperature)/235 Degrees C |
若您对上表中数据有任何疑问，请与网站联系。
