（清空日期可显示全部记录）
| 标准编号 | 标准名称 | 发布日期 | 实施日期 | 废止日期 | 替换信息 |
|---|---|---|---|---|---|
| IEC TR 62284:2003 | Effective area measurements of single-mode optical fibres - Guidance | ||||
| IEC 61189-5-3:2015 | Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 5-3: General test methods for materials and assemblies - Soldering paste for printed board assemblies | ||||
| IEC 62817:2014 | Photovoltaic systems - Design qualification of solar trackers | ||||
| IEC TR 62316:2007 | Guidance for the interpretation of OTDR backscattering traces | ||||
| IEC 61300-2-40:2000 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-40: Test - Screen testing of attenuation of single-mode tuned angled optical connectors | ||||
| IEC TR 62324:2007 | Single-mode optical fibres - Raman gain efficiency measurement using continuous wave method - Guidance | ||||
| IEC 62792:2015 | Measurement method for the output of electroshock weapons | ||||
| IEC TS 62910:2015 | Utility-interconnected photovoltaic inverters - Test procedure for low voltage ride-through measurements | ||||
| IEC TS 62916:2017 | Photovoltaic modules - Bypass diode electrostatic discharge susceptibility testing | ||||
| IEC 62148-6:2003 | Fibre optic active components and devices - Package and interface standards - Part 6: ATM-PON transceivers | ||||
| IEC 62148-11:2009 | Fibre optic active components and devices - Package and interface standards - Part 11: 14-pin active device modules | ||||
| IEC 62148-12:2004 | Fibre optic active components and devices - Package and interface standards - Part 12: Laser transmitters with a coaxial RF connector | ||||
| IEC 60332-1-2:2004+AMD1:2015 CSV | Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame | ||||
| IEC 62148-16:2009 | Fibre optic active components and devices - Package and interface standards - Part 16: Transmitter and receiver components for use with LC connector interface | ||||
| IEC 60268-9:1977 | Sound system equipment - Part 9: Artificial reverberation, time delay and frequency shift equipment | ||||
| IEC 62148-18:2014 | Fiber optic active components and devices - Package and interface standards - Part 18: 40-Gbit/s serial transmitter and receiver components for use with the LC connector interface | ||||
| IEC 60335-2-34:2012/AMD1:2015/COR1:2015 | Corrigendum 1 - Amendment 1 - Household and similar electrical appliances - Safety - Part 2-34: Particular requirements for motor-compressors | ||||
| IEC 61300-3-3:2009 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-3: Examinations and measurements - Active monitoring of changes in attenuation and return loss | ||||
| IEC 60268-17:1990 | Sound system equipment. Part 17: Standard volume indicators | ||||
| IEC 61300-3-11:1995 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-11: Examinations and measurements - Engagement and separation forces | ||||
| IEC 62150-4:2009 | Fibre optic active components and devices - Test and measurement procedures - Part 4: Relative intensity noise using a time-domain optical detection system | ||||
| IEC 62343-1:2016 | Dynamic modules - Part 1: Performance standards - General conditions | ||||
| IEC 60315-3:1989+AMD1:1999 CSV | Methods of measurement on radio receivers for various classes of emission - Part 3: Receivers for amplitude-modulated sound-broadcasting emissions | ||||
| IEC 60335-1:2010+AMD1:2013 CSV | Household and similar electrical appliances - Safety - Part 1:General requirements | ||||
| IEC 60745-2-13:2006/AMD1:2009 | Amendment 1 - Hand-held motor-operated electric tools - Safety - Part 2-13: Particular requirements for chain saws | ||||
| IEC 62343-1-2:2015 | Dynamic modules - Part 1-2: Performance standards - Tuneable chromatic dispersion compensator (non-connectorized) | ||||
| IEC 61249-2-12:1999 | Materials for printed boards and other interconnecting structures - Part 2-12: Sectional specification set for reinforced base materials, clad and unclad - Epoxide non-woven aramid laminate of defined flammability, copper-clad | ||||
| IEC 61300-3-36:2000 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-36: Examinations and measurements - Measurement methods for the inside and outside diameters of fibre optic connector ferrules | ||||
| IEC 61300-3-40:1998 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-40: Examinations and measurements - Extinction ratio of a polarization maintaining (pm) fibre pigtailed connector | ||||
| IEC 61753-2-1:2000 | Fibre optic interconnecting devices and passive components performance standard - Part 2-1: Fibre optic connectors terminated on single-mode fibre for category U - Uncontrolled environment | ||||
| IEC 61753-031-3:2014 | Fibre optic interconnecting devices and passive components - Performance standard - Part 031-3: Non-connectorized single-mode 1×N and 2×N non-wavelength-selective branching devices for Category U - Uncontrolled environment | ||||
| IEC 61753-031-6:2014 | Fibre optic interconnecting devices and passive components - Performance standard - Part 031-6: Non-connectorized single-mode 1×N and 2×N non-wavelength-selective branching devices for Category O - Uncontrolled environment | ||||
| IEC 61249-8-8:1997 | Materials for interconnection structures - Part 8: Sectional specification set for non-conductive films and coatings - Section 8: Temporary polymer coatings | ||||
| IEC 61753-052-6:2016 | Fibre optic interconnecting devices and passive components - Performance standard - Part 052-6: Single-mode fibre non-connectorized fixed attenuator - Category O in outside plant environment | ||||
| IEC 61753-052-3:2016 | Fibre optic interconnecting devices and passive components - Performance standard - Part 052-3: Single-mode fibre non-connectorized fixed attenuator - Category U in uncontrolled environment | ||||
| IEC 61636-1:2016 | Software interface for maintenance information collection and analysis (SIMICA): Exchanging test results and session information via the extensible markup language (XML) | ||||
| IEC 61753-071-2:2014 | Fibre optic interconnecting devices and passive components - Performance standard - Part 071-2: Non-connectorized single-mode fibre optic 1 × 2 and 2 × 2 spatial switches for category C - Controlled environments | ||||
| IEC 61753-082-2:2008 | Fibre optic interconnecting devices and passive components performance standard - Part 082-2: Pigtailed single-mode fibre optic 1,31/1,55 µm WWDM devices for category C - Controlled environment | ||||
| IEC 61753-083-2:2007 | Fibre optic interconnecting devices and passive components performance standard - Part 083-2: Non-connectorised single-mode fibre optic C-band/L-band WDM devices for category C - Controlled environment | ||||
| IEC 62014-4:2015 | IP-XACT, Standard Structure for Packaging, Integrating, and Reusing IP within Tool Flows | ||||
| IEC 60843-3:1993 | Helical-scan video tape cassette system using 8 mm magnetic tape - 8 mm Video - Part 3: High-band specifications for Hi 8 | ||||
| IEC 60961:1994 | Helical-scan video tape cassette system using 12,65 mm (0,5 in) magnetic tape on type L | ||||
| IEC 62526:2007 | Standard for Extensions to Standard Test Interface Language (STIL) for Semiconductor Design Environments | ||||
| IEC 61754-12:1999 | Fibre optic connector interfaces - Part 12: Type FS connector family | ||||
| IEC TS 62878-2-3:2015 | Device embedded substrate - Part 2-3: Guidelines - Design guide | ||||
| IEC TR 63051:2017 | Documentation on design automation subjects - Mathematical algorithm hardware description languages for system level modeling and verification (HDLMath) | ||||
| IEC 61754-32:2016 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 32: Type DiaLink connector family | ||||
| IEC 61120-4:1992 | Digital audio tape recorder reel-to-reel system, using 6,3 mm magnetic tape, for professional use - Part 4: Magnetic tape properties: definitions and methods of measurement | ||||
| IEC 61755-3-2:2006/COR1:2009 | Corrigendum 1 - Fibre optic connector optical interfaces - Part 3-2: Optical interface, 2,5 mm and 1,25 mm diameter cylindrical full zirconia ferrules for 8 degrees angled-PC single mode fibres | ||||
| IEC 61237-1:1994 | Broadcast video tape recorders - Methods of measurement - Part 1: Mechanical measurements |
若您对上表中数据有任何疑问，请与网站联系。
